View the full article as a PDF >., the PS Series is designed to grow with your data demands—all while providing simple management and seamless. With the EqualLogic PS and PS Series, you do not have to make a choice between scaling storage performance or expanding capacity. The PS Performance where and when you need it. The EqualLogic PSXV continues the EqualLogic tradition of performance scaling linearly with capacity.1 With up.

    Author:GAYNELL RABENHORST
    Language:English, Spanish, Portuguese
    Country:South Africa
    Genre:Religion
    Pages:435
    Published (Last):27.02.2016
    ISBN:850-8-64410-535-4
    Distribution:Free* [*Registration Required]
    Uploaded by: ELDRIDGE

    59086 downloads 129794 Views 27.31MB PDF Size Report


    Dell Ps4100xv Pdf

    This manual describes how to install PS array hardware, configure the Dell's support service is available to answer your questions about PS Series SAN . EqualLogic Storage Installation Guide 1 Rack Mounting the Array Rack See the Group Administration manual for more information. EqualLogic products are iSCSI-based storage area network (SAN) systems marketed by Dell. . Its current primary models are the PS, PS and PS with 1Gb Ethernet and 10 Gb . "Dell PS Series Configuration Guide" ( PDF).

    Page Installation Overview Failover Cluster successfully. It is recommended that you establish server roles prior to configuring a Failover Cluster, depending on the operating system configured on your cluster. Netmask Combines with the IP address to identify the subnet on which the Ethernet 0 network interface resides. Default Network address for the device used to connect subnets and forward network traffic beyond the local gateway network. You can also use the wizard to modify existing group access information on a computer for example, if the group IP address changed. Search for Select and download the latest supported initiator software and related documentation for your operating system. Double-click the executable file. The installation wizard launches. In the Welcome screen, click Next. Page 36 iSCSI target name that is generated for the volume. Host access to the volume is always through the iSCSI target name, not the volume name. By default, the volume is assigned to the default pool. Do not mount the snapshot, clone, or replica of a clustered disk to a node in the same cluster because it has the same disk signature as the original clustered disk. Page Volumes Volumes Cloning a volume creates a new volume with a new name and iSCSI target, having the same size, contents, and Thin Provisioning setting as the original volume. The new volume is located in the same pool as the original volume and is available immediately.

    Stand Alone

    Each control module has four network interface ports. These are labeled: eth0, eth1, eth2 and eth3.

    A dual control module array has four pairs of ports. The active control module can use network interfaces on the secondary control module if there is a cable connected from the corresponding port on the secondary control module to a network switch. Therefore, you should connect cables to all the network interface ports on each control module to make sure that both control modules can access an interface.

    In the example above: Control Module 0 Ethernet 0 and Ethernet 1 ports are connected to Switch 0 and Ethernet 2 and Ethernet 3 are connected to Switch 1. For Control Module 1 reverse these connections so Ethernet 0 and Ethernet 1 are connected to Switch 1, and Ethernet 2 and Ethernet 3 are connected to Switch 0.

    Up to two ports on the active control module can failover without contention.

    In the above network configuration full availability is maintained by the alternating of the switch connections between the ports of the two control modules. General rules for connecting network cables are as follows: Connect network interfaces in the following order: eth0, eth1, eth2 and eth3. If possible, connect network interfaces to different switches.

    To ensure connectivity to the network interface regardless of which control module is active, connect cables to all ports.

    In the Welcome screen, click Next. Page 36 iSCSI target name that is generated for the volume.

    EqualLogic - Wikipedia

    Host access to the volume is always through the iSCSI target name, not the volume name. By default, the volume is assigned to the default pool. Do not mount the snapshot, clone, or replica of a clustered disk to a node in the same cluster because it has the same disk signature as the original clustered disk.

    Page Volumes Volumes Cloning a volume creates a new volume with a new name and iSCSI target, having the same size, contents, and Thin Provisioning setting as the original volume. The new volume is located in the same pool as the original volume and is available immediately.

    Page Replication Replication Replication enables you to copy volume data across groups, physically located in the same building or separated by some distance. Replication protects the data from failures ranging from destruction of a volume to a complete site disaster, with no impact on data availability or performance.

    Similar to a snapshot, a replica represents the contents of a volume at a specific point in time. Dell Failover For more information on deploying your cluster with Windows Server operating systems, see the Page Troubleshooting Troubleshooting The following section describes general cluster problems you may encounter and the probable causes and solutions for each problem.

    Problem Probable Cause Corrective Action The nodes cannot access the storage The storage system is not cabled Ensure that the cables are connected system, or the cluster software is not properly to the nodes or the cabling properly from the node to the storage

    You might also like: TABACHNICK & FIDELL 2007 PDF